Loading...
8 results
Search Results
Now showing 1 - 8 of 8
- Viscosity measurements of 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMIM OTf) at high pressures using the vibrating wire techniquePublication . Sequeira, Maria Carolina; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.The goal of the present work is to contribute to the characterization of ionic liquids by measuring their viscosity at high pressures. As 1-ethyl-3-methylimidazolium trifluoromethanesulfonate (EMIM OTf) has been used as a solvent in CO2 capture processes, the temperature and pressure ranges of the measurements cover the intervals used in those processes. Measurements of the viscosity of EMIM OTf along five isotherms in the range (298–358) K and at pressures up to 50 MPa, have been performed using the vibrating wire technique in the forced mode of operation. As far as the authors are aware, these are the first measurements of this ionic liquid at pressures higher than 0.1 MPa, to be published. The viscosity results were correlated with the molar volume, using a modified hard-spheres model. The root mean square (σ) deviation of the data from the correlation is less than 0.5% The expanded uncertainty of the present viscosity data is estimated as ±2.0% at a 95% confidence level. As a complement, the pressure-viscosity coefficient has been calculated within the temperature range of the present results. Previous studies of the influence of the electric conductivity of ionic liquids, including EMIM OTf, in the vibrating wire method, have been taken into account for the present work. Complementary measurements of the density have been performed along seven isotherms in the temperature range from (298–363) K and pressures from (0.1–70) MPa. The density measurements were carried out with an Anton Paar vibrating U-tube densimeter and the raw data were corrected for viscosity effects. The density results were correlated with the temperature and pressure using a modified Tait equation. The expanded uncertainty of the present density data is estimated as ±0.2% at a 95% confidence level.
- Viscosity of liquid diethylene, triethylene and tetraethylene glycols at moderately high pressures using a vibrating wire instrumentPublication . Pereira, Marta F. V.; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.New viscosity measurements of compressed liquid diethylene glycol (DiEG), triethylene glycol (TriEG) and tetraethylene glycol (TeEG) have been performed using a vibrating wire instrument operated in the forced oscillation mode. The measurements have been carried out in a range of pressures up to 70 MPa and temperatures from (293 - 363) K, covering a total range of viscosities from (3.46 - 1.15 x 10^2) mPa,s. Complementary experimental density data were obtained for the same glycols using an Anton Paar vibrating U-tube densimeter. These measurements have been performed in a range of temperatures from about (283 - 363) K and at pressures up to about 70MPa. The viscosity results were correlated with density, using a modified hard-spheres scheme. The experimental density data were correlated, as a function of temperature and pressure, with a modified Tait-type equation. The expanded uncertainty of the present viscosity results at a 95% confidence level is estimated to be less than ±2.0% for viscosities up to 68 mPa s and less than ±2.6% for higher viscosities. The densities have an expanded uncertainty of ±0.2% at a 95% confidence level.
- Viscosity and density measurements on liquid n-heptadecane at high pressuresPublication . Sequeira, Maria Carolina; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.This article reports novel measurements of the viscosity, η, of liquid n-heptadecane at pressures up to 70 MPa, along six isotherms between 303 and 358 K. The experiments were carried out using a vibrating wire viscometer operated in the forced mode. The 303 and 313 K isotherms have a restricted range of pressures to avoid eventual solidification. The present measurements have an uncertainty less than U(η) = 0.015·η with a confidence level of 0.95. Complementary measurements of the density, ρ, were performed with the same ranges of temperature and pressure, using a DMA HP Anton Paar U-tube densimeter, with a DMA 5000 instrument as a reading unit. The overall maximum uncertainty is U(ρ) = 0.002·ρ with a confidence level of 0.95. The article provides a correlation of the viscosity of compressed liquid n-heptadecane with the molar volume, constructed by means of a scheme based on a modified hard-sphere theory, which describes the experimental data within ca. 1%. A program is provided in the Supporting Information to promptly perform interpolation of the viscosity as a function of temperature and pressure. The isothermal compressibility and the isobaric thermal expansivity were calculated from the density. Viscosity–pressure coefficients have also been determined from the viscosity.
- Viscosity and density measurements on liquid n-tetradecane at moderately high pressuresPublication . Santos, Tânia V. M.; Pereira, Marta F. V.; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.The main aim of the work is to study the viscosity and density of compressed normal tetradecane in the region of pressures from saturation to 10 MPa, where the available literature data are scarce. New measurements of the viscosity of n-tetradecane (n-C-14) along eight isotherms in the range (283-358) K and at pressures up to 70 MPa, have been performed using the vibrating wire technique in the forced mode of operation. Density measurements have also been performed along nine isotherms in the temperature range from (283 to 373) K and pressures from (0.1 to 70) MPa. The vibrating wire viscosity results were correlated with density, using a modified hard-spheres scheme. The root mean square (rms) deviation of the data from the correlation is less than 0.32% and the maximum absolute relative deviation is less than 1.0%. The expanded uncertainty of the present viscosity data is estimated as +/- 1.5% at a 95% confidence level. The density results were correlated with the temperature and pressure using a modified Tait equation. The expanded uncertainty of the present density data is estimated as +/- 0.2% at a 95% confidence level. The isothermal compressibility and the isobaric thermal expansion were calculated by differentiation of the modified Tait equation. The uncertainties of isothermal compressibility and the isobaric thermal expansion are estimated to be less than +/- 1.7% and +/- 1.1%, respectively, at a 95% confidence level. The results are compared with the available literature data. (C) 2017 Elsevier B.V. All rights reserved.
- Tris(2-ethylhexyl) trimellitate (TOTM) a potential reference fluid for high viscosity. Part I: Viscosity measurements at temperatures from (303 to 373) K and pressures up to 65MPa, using a novel vibrating-wire instrumentPublication . Diogo, João C. F.; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.The article reports viscosity measurements of compressed liquid tris(2-ethylhexyl) trimellitate or 1,2,4- Benzenetricarboxylic acid, tris(2-ethylhexyl) ester (TOTM) which is an important plasticizer in the polymer industry and has wide applications as a lubricant. Nevertheless, the main motivation for the present work is to propose TOTM as a plausible candidate for an industrial viscosity reference fluid for high viscosity, high pressure and high temperature. This kind of reference fluid is presently on demand by oil industries and the International Association for Transport Properties is developing efforts aiming to select appropriate candidates and to establish the corresponding reference data. The viscosity measurements were performed with a novel vibrating wire sensor. The new instrument was designed for operation at high pressures (up to 100MPa) and temperatures up to 373 K. The present measurements were obtained using the vibrating wire sensor in the forced oscillation or steady-state mode of operation. The viscosity measurements were carried out up to 65MPa and at six temperatures from (303 to 373) K. The viscosity results were correlated with density, using a modified hard-spheres scheme. The root mean square deviation of the data from the correlation is 0.53% and the maximum absolute relative deviation was less than 1.7%. The expanded uncertainty of the present viscosity results, at a 95% confidence level, is estimated to be less than 2% for viscosities up to 68mPa s, less than 2.6% for viscosities between (69 and 268) mPas and less than 3% for higher viscosities. The TOTM density data necessary to compute the viscosity results were measured using a vibrating Utube densimeter, model DMA HP and are described in part II of the present work. No literature data above atmospheric pressure could be found for the viscosity of TOTM. As a consequence, the present viscosity results could only be compared upon extrapolation of the vibrating wire data to 0.1 MPa. Independent viscosity measurements were performed, at atmospheric pressure, using an Ubbelohde capillary in order to compare with the vibrating wire results, extrapolated by means of the above mentioned correlation. The two data sets agree within 1%, which is commensurate with the mutual uncertainty of the experimental methods. Comparisons of the literature data obtained at atmospheric pressure with the present extrapolated vibrating-wire viscosity measurements have shown an agreement within 2% for temperatures up to 339K and within 3.3% for temperatures up to 368 K.
- Viscosity measurements of poly(ethyleneglycol) 400 [PEG 400] at temperatures from 293 K to 348 K and at pressures up to 50 MPa using the vibrating wire techniquePublication . Sequeira, Maria Carolina; Pereira, Marta F. V.; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.The article reports new measurements of the viscosity of Poly(ethyleneglycol) 400 [PEG 400] in the range (293–348) K and pressures up to 50 MPa. Complementary measurements of the density of the same sample of PEG 400 have been made covering the ranges of temperature and pressure, (293–353) K and (0.1–50) MPa, respectively. The viscosity measurements were performed using the vibrating wire technique in the forced mode of oscillation and the density measurements were carried out with an Anton Paar vibrating U-tube densimeter. The density raw data were corrected for viscosity effects. The overall uncertainty of the viscosity measurements is estimated to be less than ±2% for viscosities up to 68 mPa s and less than ±2.6% for higher viscosities. The densities have an estimated overall uncertainty of ±0.2%. The rheological behaviour of Poly(ethylene Glycol) 400 has also been studied, using a cone-plate Brookfield viscometer, in a temperature range between (293 and 333) K. The measurements were carried out at shear rates up to 20 s−1 and shear stresses up to 2.20 Pa and have evidenced Newtonian behaviour. The viscosity data obtained were correlated by means of a modified hard-sphere based correlation technique. The relative root mean square, rms, deviation of the experimental results from the correlation equations is 0.54%, and their bias is practically zero. The density data obtained were correlated using a Tait-type equation. As a complement of the present study, the surface tension of PEG 400 was measured by the pendant drop method. This study aims to be useful for viscosity measurements using capillary viscometers. As far as the authors are aware, the present viscosity measurements are the first results to be published for PEG 400 at pressures higher than atmospheric pressure.
- Viscosity of liquid diethylene, triethylene and tetraethylene glycols at moderately high pressures using a vibrating wire instrumentPublication . Pereira, Marta F. V.; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.New viscosity measurements of compressed liquid diethylene glycol (DiEG), triethylene glycol (TriEG) and tetraethylene glycol (TeEG) have been performed using a vibrating wire instrument operated in the forced oscillation mode. The measurements have been carried out in a range of pressures up to 70 MPa and temperatures from (293–363) K, covering a total range of viscosities from (3.46–1.15 × 102) mPa⋅s. Complementary experimental density data were obtained for the same glycols using an Anton Paar vibrating U-tube densimeter. These measurements have been performed in a range of temperatures from about (283–363) K and at pressures up to about 70 MPa. The viscosity results were correlated with density, using a modified hard-spheres scheme. The experimental density data were correlated, as a function of temperature and pressure, with a modified Tait-type equation. The expanded uncertainty of the present viscosity results at a 95% confidence level is estimated to be less than ±2.0% for viscosities up to 68 mPa s and less than ±2.6% for higher viscosities. The densities have an expanded uncertainty of ±0.2% at a 95% confidence level.
- Studying the PEG familyPublication . Sequeira, Maria Carolina; Avelino, Helena Maria da Nóbrega Teixeira; Caetano, Fernando J. P.; Fareleira, João M. N. A.The main goal of this line of research is the realisation of experimental measurements of thermophysical properties of a homologous series of ethylene and polyethylene glycols [H(OCH2CH2)nOH], and the development of correlation methods, with an accuracy adequate for the applications. Ethylene glycols and poly (ethylene) glycols (PEG) are widely used in many industrial applications as green solvents and as components of important sustainable processes as they are considered environmentally acceptable compounds [1,2]. Liquid Poly(ethyleneglycols) [PEGs] are in general considered as green solvents. They are non-volatile; their toxicity is very low, such that they are being used as food additives [3]. PEGs have been found to be biodegradable by bacteria in soil or sewage, but the ability of bacteria to biodegrade PEG decreases with increasing molecular weight [3]. The study of this series of compounds is important in many respects, not only because it is aimed at the study of PEGs which have innumerable practical applications but also because this study can be useful to monitor the degree of polymerization in the production of PEGs, themselves. In the present work, the viscosity of three ethylene glycols, namely diethylene, triethylene and tetraethylene glycols [4] and PEG 400 were measured with high accuracy using the vibrating wire technique at moderately high pressures. Complementary experimental density, surface tension and rheological behavior were obtained for the same liquids. One of the aims of the work is to analyse the relation of the present results with those obtained before for CO2 saturated PEG400 mixtures